Specifications
ACOUSTICAL1 | |||
Operating Frequency Range2 | 75 Hz – 20 kHz | ||
Frequency Response3 | 80 Hz – 16 kHz ±4 dB | ||
Phase Response | 300 Hz – 18 kHz ±60 degrees | ||
Linear Peak SPL4 | 118.5 dB with crest factor >14 dB (M-noise), 113 dB (Pink noise), 115.5 (B‑noise) | ||
COVERAGE | |||
Horizontal Coverage | 100° | ||
Vertical Coverage | 100° | ||
TRANSDUCERS | |||
Low Frequency | Two 5‑inch cone drivers; 8 Ω nominal impedance | ||
High Frequency | One 1‑inch metal dome tweeter; 8 Ω nominal impedance | ||
AUDIO INPUT | |||
Type | Differential, electronically balanced | ||
Maximum Common Mode Range | ±15 V DC, clamped to earth for voltage transient protection | ||
Connectors | Phoenix 5‑pin Male; SwitchCraft 5‑pin Male; ECO‑M 7‑pin Male (two pins for 48 V DC power, three pins for balanced audio) | ||
Input Impedance | 10 kΩ differential between positive (+) and negative (–) audio pins | ||
Wiring5 | Phoenix 5‑pin Male Pin 1: DC Power (‑) Pin 2: DC Power (+) Pin 3: Chassis/earth through 1 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies Pin 4: Audio (‑) Pin 5: Audio (+) | SwitchCraft EN3 5‑pin Male Pin 1: DC Power (‑) Pin 2: DC Power (+) Pin 3: Chassis/earth through 1 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies Pin 4: Audio (‑) Pin 5: Audio (+) | ECO‑M 7‑pin Male5 Pin 1: DC Power (‑) Pin 2: DC Power (+) Pin S: Chassis/earth through 1 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies Pin 5: Audio (‑) Pin 6: Audio (+) |
Nominal Input Sensitivity | –8.0 dBV (0.4 V rms) continuous average is typically the onset of limiting for noise and music | ||
Input Level | Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker. | ||
AMPLIFIER | |||
Type | 3‑channel, class D | ||
Total Output Power6 | 650 W peak | ||
THD, IM, TIM | < 0.02% | ||
Cooling | Convection | ||
DC POWER | |||
Connector | Phoenix 5‑pin Male; SwitchCraft 5‑pin Male; ECO‑M 7‑pin Male (two pins for 48 V DC power, three pins for balanced audio) | ||
Safety Rated Voltage Range | 48 V DC | ||
RMS NETWORK (OPTIONAL) | |||
Equipped with two‑conductor twisted‑pair network, reporting all operating parameters of amplifiers to system operator’s host computer. | |||
PHYSICAL | |||
Dimensions | W: 6.85 in (174 mm) x H: 18.00 in (457 mm) x D: 7.70 in (196 mm) | ||
Weight | 17 lb (7.7 kg) | ||
Enclosure | Premium multi‑ply birch with slightly textured black finish | ||
Protective Grille | Powder‑coated, hex‑stamped steel with black mesh | ||
Rigging | Three 3/18‑inch‑16 or metric M10 nut plates | ||
Notes
Loudspeaker system predictions for coverage and SPL are available in Meyer Sound’s MAPP System Design Tool.
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics.
Free‑field, measured with 1/3 octave frequency resolution at 4 m.
Linear Peak SPL is measured in free‑field at 4 m referred to 1 m. Loudspeaker SPL compression measured with M‑noise at the onset of limiting, 2‑hour duration, and 50‑degree C ambient temperature is < 2 dB.
M-noise is a full bandwidth (10 Hz–22.5 kHz) test signal developed by Meyer Sound to better measure the loudspeaker’s music performance. It has a constant instantaneous peak level in octave bands, a crest factor that increases with frequency, and a full bandwidth Peak to RMS ratio of 18 dB. The presence of a greater‑than (>) symbol with regard to crest factor indicates it may be higher depending on EQ and boundary loading.
Pink noise is a full bandwidth test signal with Peak to RMS ratio of 12.5 dB.
B-noise is a Meyer Sound test signal used to ensure measurements reflect system behavior when reproducing the most common input spectrum, and to verify there is still headroom over pink noise.
Pins 3 and 4 not used in ECO‑M connector.
Peak power based on the maximum unclipped peak voltage the amplifier will produce into the nominal load impedance.
Compliance
