Skip to main content

Meyer Sound Documentation

Datasheet — MM-10

Miniature Subwoofer
In this section:
meyer-blue-rule-line.png
MM-10_Perspective_01B.jpg
MM-10_Dimensions_cog.ai

MM-10 Loudspeaker and Dimensions

meyer-blue-rule-line.png
Specifications (All Models)
meyer-blue-rule-line.png

ACOUSTICAL1

Operating Frequency Range2

33 Hz – 228 Hz

Frequency Response3

35 Hz – 208 Hz ±4 dB

Phase Response

38 Hz – 138 Hz ±45°

Linear Peak SPL4

118.5 dB with crest factor > 11 dB (M-noise), 117.5 dB (Pink noise), 120.5dB (B-noise)

COVERAGE

360°

TRANSDUCERS

Low Frequency

One 10 inch cone driver with 2-inch voice coil; 4 Ω nominal impedance

AUDIO INPUT

Type

Differential, electronically balanced

Maximum Common Mode Range

±5 V DC

Input Impedance

10 kΩ electronically balanced

Nominal Input Sensitivity

–2.0 dBV (0.8 V rms) continuous is typically the onset of limiting for noise and music

Input Level

Audio source must be capable of producing +16 dBV (6.3 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.

AMPLIFIER

Type

Class-D

Total Output Power5

440 W peak

THD, IM, TIM

< 0.02%

Cooling

Convection

PHYSICAL

Dimensions

W: 19 in (483 mm) x H: 11 in (279 mm) x D: 12 in (305 mm)

MM-10XP Weight

26.7 lb (12.11 kg)

MM-10AC Weight

28.2 lb (12.79 kg)

MM-10ACX Weight

30.8 lb (13.97 kg)

Enclosure

Premium multi-ply birch with slightly textured black finish

Protective Grille

Powder-coated, hex-stamped steel with black mesh screen

Rigging

Top and side nut plates available with 3/8-inch or M10 threads. The optional MUB-MM10 U-bracket enables mounting of the MM-10 on walls and ceilings at adjustable angles.

COMPLIANCE

Safety Agency Certifications

Standard for Audio/video, information, and communication technology equipment:

  • IEC/UL/CSA 62368-1 3rd and IEC/BS/EN/ 62368-1 2nd

  • UL 2043 tested Suitable for use in air handling spaces (MM-10XP model only)

EMC Certification

CE and FCC Part 15 Emission Class B emission limits applied.

Notes (All Models)
meyer-blue-rule-line.png
  1. Loudspeaker system predictions for coverage and SPL are available in Meyer Sound’s MAPP System Design Tool.

  2. Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics.

  3. Free field, measure with 1/3-octave frequency resolution at 4 meters.

  4. Measured in half-space with pink noise at 4 m, 1/3-octave frequency resolution.

    Linear Peak SPL is measured in half-space at 4 m referred to 1 m. Loudspeaker SPL compression measured with M-noise at the onset of limiting, 2-hour duration, and 50-degree C ambient temperature is <2 dB.

    M-noise is a full bandwidth, (10 Hz–22.5 kHz) test signal developed by Meyer Sound to better measure the loudspeaker’s music performance. It has a constant instantaneous peak level in octave bands, a crest factor that increases with frequency, and a full bandwidth Peak to RMS ratio of 18 dB. The presence of a greater-than (&gt;) symbol with regard to crest factor indicates it may be higher depending on EQ and boundary loading.

    Pink noise is a full bandwidth test signal with Peak to RMS ratio of 12.5 dB.

    B-noise is a Meyer Sound test signal used to ensure measurements reflect system behavior when reproducing the most common input spectrum, and to verify there is still headroom over pink noise. Peak power based on the maximum unclipped peak voltage the amplifier will produce into the nominal load impedance.

  5. Peak power based on the maximum unclipped voltage the amplifier will produce into the nominal load impedance.

MM-10XP SPECIFICATIONS
meyer-blue-rule-line.png

REAR PANEL

Audio/Power Connector

Phoenix 5-pin male or EN3 5-pin male (two pins for DC power, three pins for balanced audio)

Wiring

Pin 1: DC power negative (–) Pin 2: DC power positive (+)

Pin 3: Balanced audio shield, chassis/earth Pin 4: Balanced audio (–)

Pin 5: Balanced audio (+)

Input Polarity Switch

Reverses audio input polarity between pins 4 and 5

LED

Displays loudspeaker status

DC POWER

Safety Agency Rated Operating Range6

48 V DC

CURRENT DRAW

Idle Current

0.16 A rms

Maximum Long-Term Continuous Current (>10 sec)

0.90 A rms

Burst Current (<1 sec)

2.5 A rms

Maximum Instantaneous Peak Current

3.0 A peak

Inrush Current

< 7.0 A peak

Meyer Sound MPS IntelligentDC Power Supply Required

See MPS IntelligentDC Power Supply for specifications

MM-10AC Specifications
meyer-blue-rule-line.png

REAR PANEL

Audio Connector7

3-pin XLR female input with XLR male loop output

Wiring

Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies

Pin 2: Signal + Pin 3: Signal –

Case: Earth ground and chassis

Input Polarity Switch

Reverses audio input polarity between pins 2 and 3

AC Power Connector

powerCON 20 input with loop output

LED

Displays loudspeaker status

AC POWER

Automatic Voltage Selection

90–265 V AC

Safety Rated Voltage Range

100–240 V AC, 50–60 Hz

Turn-on and Turn-off Points

90 V AC turn-on, no turn-off; internal fuse-protection above 265 V AC

CURRENT DRAW8

Idle Current

0.13 A rms (115 V AC); 0.13 A rms (230 V AC); 0.14 A rms (100 V AC)

Maximum Long-Term Continuous Current (>10 sec)

0.40 A rms (115 V AC); 0.25 A rms (230 V AC); 0.46 A rms (100 V AC)

Burst Current (<1 sec)

0.9 A rms (115 V AC); 0.4 A rms (230 V AC); 1.1 A rms (100 V AC)

Maximum Instantaneous Peak Current

2.0 A peak (115 V AC); 1.4 A peak (230 V AC); 2.3 A peak (100 V AC)

Inrush Current

4.0 A peak (115 V AC); 2.4 A peak (230 V AC); 4.0 A peak (100 V AC)

MM-10ACX Specifications
meyer-blue-rule-line.png

REAR PANEL

Audio Connector

3-pin XLR female input

Wiring

Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies

Pin 2: Signal + Pin 3: Signal –

Case: Earth ground and chassis

Input Polarity Switch

Reverses audio input polarity between pins 2 and 3 (subwoofer only)

Input Select Switch9

Determines whether the subwoofer receives it source signal from the subwoofer input or satellite inputs (summed)

Gain Knob10

Adjusts the subwoofer signal from completely attenuated to +10 dB

AC Power Connector

powerCON 20 input with loop output

Satellite Loudspeaker Connectors11

Two XLR female inputs; Two Phoenix 5-pin male or EN3 5-pin female outputs (two pins for DC power, three pins for balanced audio)

LED

Displays loudspeaker status

AC POWER

Automatic Voltage Selection

90–265 V AC

Safety Rated Voltage Range

100–240 V AC, 50–60 Hz

Turn-on and Turn-off Points

90 V AC turn-on, no turn-off; internal fuse-protection above 265 V AC

CURRENT DRAW (SUBWOOFER ONLY)12

Idle Current

0.21 A rms (115 V AC); 0.20 A rms (230 V AC); 0.23 A rms (100 V AC)

Maximum Long-Term Continuous Current (>10 sec)

0.48 A rms (115 V AC); 0.31 A rms (230 V AC); 0.55 A rms (100 V AC)

Burst Current (<1 sec)

1.1 A rms (115 V AC); 0.6 A rms (230 V AC); 1.3 A rms (100 V AC)

Maximum Instantaneous Peak Current

2.2 A peak (115 V AC); 1.6 A peak (230 V AC); 2.5 A peak (100 V AC)

Inrush Current

6.6 A peak (115 V AC); 3.7 A peak (230 V AC); 7.2 A peak (100 V AC)

CURRENT DRAW (WITH TWO MM-4XP)13

Idle Current

0.32 A rms (115 V AC); 0.26 A rms (230 V AC); 0.36 A rms (100 V AC)

Maximum Long-Term Continuous Current (>10 sec)

0.90 A rms (115 V AC); 0.51 A rms (230 V AC); 1.02 A rms (100 V AC)

Burst Current (<1 sec)

2.5 A rms (115 V AC); 1.3 A rms (230 V AC); 3.0 A rms (100 V AC)

Maximum Instantaneous Peak Current

4.5 A peak (115 V AC); 2.8 A peak (230 V AC); 5.0 A peak (100 V AC)

Inrush Current

7.6 A peak (115 V AC); 4.4 A peak (230 V AC); 8.4 A peak (100 V AC)

Notes (MM-10XP | MM-10AC | MM-10ACX)
meyer-blue-rule-line.png
  1. Tolerates voltage drops up to 30% with long cable runs.

  2. Audio loop output only included on the MM-10AC model.

  3. Current draw values for a single MM-10AC. AC Loop output not used.

  4. Input Select switch only included on the MM-10ACX model.

  5. Gain knob only included on the MM-10ACX model.

  6. Satellite loudspeaker connectors only included on the MM-10ACX model.

  7. Current draw values for one MM-10ACX with no satellite loudspeakers connected. AC Loop output not used.

  8. Current draw values for one MM-10ACX with two MM-4XP satellite loudspeakers connected. AC Loop output not used.